大家在查： run President N-Tech Weiqi 爱森斯坦前景展望金州勇士份活杰克·斯尼德跌下来 abrasives

拉拔

na.【冶】draft; drawing
网络draw out; pull-out; Wire Drawing

拉拔

英-汉网络释义

拉拔

drawing

材料力学常用英语词汇 ... 结构抗撞毁性 Structural crashworthiness 拉拔 Drawing 破坏机构 Collapse mechanism ...

draw out

机械英语词汇|各类常用英语词汇 ... draft taper 拔模锥度 draw out 拉拔 fit tolerance 配合公差 ...

pull-out

laid out_翻译 ... 消亡： Die out 拉拔： pull-out 吹脱： blow-out ...

draft

材料成型工艺基础部分 - 豆丁网 ... 辗压： tamping drum 拉拔： draft 2.3 塑性加工工艺设计工艺规程： process specification ...

Wire Drawing

金属加工液在不同机械加工使用场合的代号表示 ... Ironing,power spinning 挤压 Wire drawing 拉拔 Forming stamping 锻造、 …

drawing-down

英汉日模具用语集——d ... drawing writ management 图面文书管理 drawing-down 拉拔 drawn panel 拉深面板 ...

例句：

The pull-out test results obtained with a modified material test system (MTS) indicate that SAWI is of good interlayer bonding capability .

利用改进材料试验系统（MTS ）的夹具进行的拉拔试验表明，SAWI 具有很好的层间结合能力；

This investigation proves that the designed tester can be applied to single fiber pull-out test effectively ; and the test results are exact.

结果表明，设计的试验装置和试验方法能较好地进行单根纤维的拉拔试验，具有较高的准确性和精度。

It computes the best optimal to minimize the drawing stress with a same ratio of section reduction and Lagrange multiplier .

在保证拉拔过程中应力达到最小，拉拔道次和各截面缩减率一定的情况下，获得最优几何半角。

and processing a tubing rolled out from the exit of the three -roller planetary rolling machine into a finished product by drawing .

从三辊行星轧机的出口处轧出的管材通过拉拔加工成成品。

Therefore , for estimating strength of the new concrete construction, pull-out test has the potential to be used in practice.

因此对于新建工程之混凝土强度评估，拉拔试验将是具有推广潜力的检测技术。

U, I or H sections , not further worked than hot - rolled, hot-drawn or extruded, of a height of less than 80mm.

槽钢、工字钢及 H 型钢，除热轧、热拉拔或热挤压外未经进一步加工，截面高度低于 80 毫米。

Recently, the main tests for the interface characteristics of reinforced soil are pullout test and shear test .

目前，国内外对于加筋土的界面特性试验仍然以直剪试验与拉拔试验为主。

The aluminum tube produced by the optimized drawing die possesses eligible dimensions and smooth inner surfaces .

采用修正后的模具拉拔出的矩形截面铝合金管材尺寸合格、表面光亮。

By dyed sand observation method in pullout tests , the pullout mechanism of georgia with strengthening ribs reinforced soil was analyzed .

采用染色砂法，通过带加强肋土工格栅的拉拔试验进行了拉拔力机理分析。

The pickling free drawing process is compared with the tradition production process by production experiments .

无酸洗拉拔工艺与常规生产工艺进行了生产实验比较。

and step 3 , the puller is pulled , the detecting pin is pulled from the wall body and the data on the dial of the puller is read .

步骤 3 ，拉拔拉拔器，将检测钉从墙体拔出，读出拉拔器上的表盘上的数据。

The strain of the proeutectoid ferrite in hypoeutectoid steel drawing was measured and analyzed by quantitative metallography.

采用定量金相法分析计算了亚共析钢拉拔变形中先共析铁素体应变量。

Due to proper confinement, the failure mode for most of the specimens was pullout mode .

由于受适当之围束，所有试体均以拉拔形式破坏。

The micro structures change of super-high strength of austenite stainless still silk in multi-ply drawing were analysed .

分析了超高强度奥氏体不锈钢丝在多道次拉拔过程中的组织变化。

拉拔

拉拔