大家在查： Dhabi 历代出血 shorting insurance companies 晴天 drunken 高高在上 squaring 无序

熔覆

网络Fused Deposition Modeling; Cladding; Laser Cladding

熔覆

网络释义

熔覆

Fused Deposition Modeling

丝状材料选择性熔覆（Fused Deposition Modeling）快速原型工艺是一种不依靠激光作为成型能源、而将各种丝材（如工程塑 …

Cladding

拨打前所需材料 ... Welding/ 焊接 Cladding/ 熔覆 Sintering/ 快速成型 ...

Laser Cladding

...id Prototyping, RP)技术与激光熔覆(Laser Cladding)技术相结合，采用高功率激光器在基底或前一层金属上生成一个移动的金 …

Fused Depositio Modeling

丝状材料选择性熔覆（Fused Depositio Modeling）快速原型工艺是一种不依靠激光作为成型能源、而将各种丝材加热溶化的成 …

FDM-Fused Deposition Modeling

　　4.丝状材料选择性熔覆(FDM-Fused Deposition Modeling)，这是一种不使用激光器的方法，技术关键在于喷头的设计，喷头在 …

例句：

There's no interior cladding , vapor comes out of ducts in the ceiling , and the only windows are too high to see out of.

飞机上没有内部熔覆层，顶部的通道管道会喷出蒸汽，窗户都开得很高，无法朝外看。

The laser cladding processing was applied to carry out cladding bronze alloy on the surface of nodular cast iron .

运用激光熔覆方法在球墨铸铁基体上熔覆铜合金涂层。

Test results show that this technique is helpful to characterize the residual stress distribution . . .

此方法有助于准确测定熔覆层的残余应力分布。

The golden cladding of the Visitor Center echoes the "solar bark " , one of the motifs depicted on the Sky Disc .

金熔覆的游客中心相呼应的 “太阳能树皮 ”，其中一个图案描绘的天空光盘。

and since the YAG laser fusion will not affect the non radiated part , it has high repair quality.

同时由于 YAG 激光熔覆对非激光照射部位没有或影响极小，修复质量高；

The corrosion resistance of the overlaid layer was assessed by means of the polarization curve .

利用极化曲线评价了熔覆层的耐蚀性。

The microhardness of the cladding layer was measured by microhardness tester , and its microstructure was observed by SEM .

利用维氏硬度计测试了其显微硬度，用扫描电镜分析了激光熔覆层的微观形貌。

The stress distribution of cladding layer can be ameliorate with preheating before cladding and thermal retardation after cladding.

熔覆件整体的熔前预热和熔后保温。可以改善熔覆层的应力分布。

Compared with the substrate , hardness of the cladding layer improves significantly .

与被强化基体相比，熔覆层的硬度得到显著提高。

The interface peak of stretching stress of phase changing is relieved, and satisfaction of stress status of cladding layer is obtained .

界面的相变拉应力峰被消除 .得到了应力分布状态较好的激光熔覆层。

The influences of the process parameters on microstructure and properties of the cladding layer were discussed .

探讨了工艺参数对熔覆层组织、性能的影响。

A new technology to prepare thick film resistors directly by laser micro -cladding resistor pastes on ceramic substrate is introduced.

应用一种新工艺 -激光微细熔覆电阻浆料直写电阻技术，在陶瓷基板上制备厚膜电阻。

The results show that the width and height decrease with the increase of the scanning speed .

结果表明，熔覆层的宽度、高度随扫描速率的增大而减小；

A new conception , average powder density defined as the powder quantity clad on unit area of substrate surface has been put for ward.

提出了粉末分布密度这一新概念，即同步送粉激光熔覆时基体单位面积上分布的覆层粉末质量。

The checkered cladding does obscure the details , but the overall feel of the vehicle is definitely there .

在格仔熔覆并不掩盖了细节，但总的感觉车辆肯定是有。

The width changes little with the change of powder feeding rate and the height increases with the increase of powder feeding rate .

熔覆层的宽度随送粉速率的改变变化不大；熔覆层的高度随送粉速率的增加而增加；

In the cladding , the longitudinal stress is biggest, the lateral stress is second, and the thickness direction stress is smallest.

熔覆层纵向应力最大，横向应力次之，厚度方向应力最小；

熔覆

熔覆

Fused Deposition Modeling

Cladding

Laser Cladding

Fused Depositio Modeling

FDM-Fused Deposition Modeling

热词推荐

大家在看